Round tabletops / parallel boards

Circle glue-up calculator

Plan a round tabletop from shorter board blanks, not a full-length rectangle. See which lengths cover the curve, add your trimming allowances, then check how those blanks fit your stock.

SawNest round tabletop blank plan

Parallel, equal-width boards

Start with the finished circle.

Use the usable width after jointing. All boards run in one direction and are centered across the glue-up. This is not a segmented ring or radial stave layout.

Examples, not recommended allowances. Radius allowance expands the whole circle; end allowance extends each blank length. These are separate. Inches accept fractions; a 1/16 in increment rounds lengths upward, never to nearest.

Centered blank layout

Cover the whole curve.

9board blanks
54in glue-up width
15.37bd ft in listed blanks
B1B2B3B4B5B6B7B8B9

Finished circle Circle plus radial trim

Top view. Solid rectangles are blanks, not finished parts. All lengths are centered left-to-right. Blank IDs match the cut list below. Diagram is not a printable template.

Blank cutting list

Keep these boards in order.

Finished diameter 48 in; radial trim 0.25 in; end trim 0.5 in at each end. Board thickness 1 in. Lengths rounded up to 0.0625 in.

Each row is one blank; dimensions are in inches. Board B1 is at the top of the diagram.
BlankWidthCovering chord*Cut blank lengthQty
B1624.2538725.31251
B2638.108439.1251
B3645.036146.06251
B4648.1274449.18751
B5648.549.51
B6648.1274449.18751
B7645.036146.06251
B8638.108439.1251
B9624.2538725.31251

*The longest chord inside that board strip, including radial trim, but before end trim. Cut to the rounded blank length, not the chord. Displayed cut lengths are rounded upward to at most six decimal places; the CSV retains calculation precision. Total blank length: 368.875 in. Board feet use listed blank dimensions, not a rough-lumber purchase or finished yield estimate. Printing includes the confirmed stock plan if one is open.

Review grain and color, jointed widths, clamping alignment and actual stock before cutting. Center and dry-fit the blanks. Final circle trimming and any joinery are separate shop operations; the diagram is not a machine sequence.

Optional stock planning

Fit these blank lengths onto your stock.

Enter usable board length after damaged ends are removed. This transfers the rounded lengths into SawNest’s existing linear optimizer. It does not rip wider stock, account for defects or change the glue-up geometry.

Unlimited matching stock boards are assumed. Price 0 means no cost estimate, not free material. An insufficient stock length produces an incomplete plan.

The geometry that keeps the edges covered

Start with radius R = finished diameter / 2 + radial trimming allowance. The number of equal-width blanks is ceil(2R / usable board width), centered as a group across the circle.

For each board strip, find its nearest distance d to the centerline. If the strip crosses the centerline, d is zero. The longest chord in that strip is 2 x sqrt(R² - d²). Add the end allowance twice, then round the resulting blank length upward to your selected increment.

Worked example: a 24-inch circle, four 6-inch boards

With no radial or end trim, the two middle blanks need 24 inches. Each outer strip runs from 6 to 12 inches away from the center, so its required chord is 2 x sqrt(12² - 6²), approximately 20.78461 inches. Rounded up to 1/16 inch, each outer blank is 20.8125 inches (20 13/16). A centerline calculation at 9 inches would give only about 15.87 inches and leave the circle uncovered near the inner edge.

Before turning the numbers into a tabletop

  • Use consistent, actual jointed widths. A nominal 1 x 6 is not assumed to be 6 inches wide.
  • Center every blank along its length and keep the illustrated board order. Uneven alignment can move material away from the circle.
  • Allow for your clamping, glue-up and trimming process. The default allowances are examples only.
  • Review grain, appearance and stock defects in person. The calculation does not engineer the tabletop, its base, wood movement or attachments.
  • The optional linear plan includes crosscut kerf between blanks, but not rip waste, milling, curve cutting or unlimited reuse of scraps.

Use the board-foot purchase worksheet for a separately priced rough-lumber list, or the tape-measure calculator to review fractional marks. If your blanks have different widths, use a custom layout instead of forcing them into this equal-width model.

Common glue-up questions

Why not calculate a chord through each board center?

A centerline chord can be shorter than the circle inside the board strip. This calculator uses the strip edge nearest the circle center, or the diameter when the strip crosses the center, to cover the entire circle.

Does nominal 1 x 6 stock provide a 6-inch glue-up width?

Not necessarily. Enter the actual usable width after jointing and surfacing. The board count and geometry depend on that finished usable width, not the lumber label.

Does this plan a segmented or radial tabletop?

No. It plans parallel, equal-width rectangular boards centered across a circular top. Segmented rings, angled staves, curved edge joints, joinery and structural design are outside its scope.